INITIAL SETUP:
WS-9060U-IT FORECAST STATION
Quick Setup Guide
Do not mix old and new batteries. Do not mix alkaline,
standard, or rechargeable batteries
INTRODUCTION:
Congratulations on purchasing this state-of-the-art
weather station as an example of innovative design and
quality piece of engineering. Providing time, calendar,
weather forecast, moon phase, indoor and outdoor
temperature, indoor and outdoor relative humidity. This
unit will never keep you guessing on current and future
weather conditions.
1.
2.
3.
Install batteries (2-AAA LR3, 1.5V) into the Thermo-
hygro Transmitter according to polarity.
Install batteries (2-AAA LR3, 1.5V) into the Weather
Station according to polarity.
Place the transmitter and weather station 5-10 feet
apart. When the batteries are inserted, the weather
station will start receiving data signal from the
transmitter. The outdoor temperature and humidity
data should be displayed on the weather station.
If this does not happen after 2 minutes, the batteries
will need to be removed from both units and reset
from step 1.
The Weather Station
LCD
Display
4.
5.
If the outdoor temperature and humidity are
displayed for 15 minutes, the transmitter can be
placed outside.
Function key
Note:
When changing batteries in the units, ensure the batteries
do not spring free from the contacts. Always wait at least
15 minutes after removing the batteries before reinserting,
otherwise start up and transmission problems may occur.
Hanging
hole
Battery
compartment
TO INSTALL AND REPLACE BATTERIES IN THE
THERMO-HYGRO TRANSMITTER
The outdoor thermo-hygro transmitter uses 2 x AAA, IEC
LR3, 1.5V batteries. To install and replace the batteries,
please follow the steps below:
Function keys
Stand
1.
2.
Remove the battery cover.
Insert the batteries, observing the
correct polarity (see battery
compartment marking).
FEATURES:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
12/24 hour time display
Calendar display (year shows only in set mode)
Display 8 Moon phases throughout the year
Weather forecasting with weather tendency indicator
Indoor and outdoor temperature display with
MIN/MAX records
3.
Replace the battery cover on the unit.
Note:
When changing batteries in any of the units,
all units need to be reset by following the
ꢀ
ꢀ
ꢀ
ꢀ
Temperature display in ºC/ ºF
setting up procedures. This is due to a random security
code assigned by the transmitter at start-up. This code
must be received and stored by the weather station in the
first 3 minutes of power being supplied to the transmitter.
Indoor and outdoor humidity display
Humidity data display as RH%
Low battery indicator
1
2
TO INSTALL AND REPLACE BATTERIES IN THE
WEATHER STATION
MANUAL SETTINGS: The SET key will move you through
the program menu. The + key will change a value.
The weather station uses 2 x AAA, IEC LR3, 1.5V
batteries. To install and replace the batteries, please follow
the steps below:
12/24-HOUR TIME: Hold the SET key and 12h or 24h will
flash. Use the + key to select 12-hour or 24-hour time.
Press and release the SET key to confirm and continue.
HOUR: The Hour will flash. Use the + key to select the
Hour. Press and release the SET key to confirm and
continue.
MINUTES: The Minutes will flash. Use the + key to select
the Minutes. Press and release the SET key to confirm
and continue.
1.
Insert finger or other solid
object in the space at the
bottom center of the
battery compartment and
lift up to remove the
cover.
2.
3.
Insert batteries observing
the correct polarity (see
marking).
YEAR: The Year will flash. Use the + key to select the
Year (the year will not display on the weather station).
Press and release the SET key to confirm and continue.
MONTH: The Month will flash. Use the + key to select the
Month. Press and release the SET key to confirm and
continue.
Replace compartment
cover.
BATTERY CHANGE:
DATE: The Date will flash. Use the + key to select the
Date. Press and release the SET key to confirm and
continue.
It is recommended to replace the batteries in all units on
an annual basis to ensure optimum accuracy of these
units.
°F/°C TEMPERATURE: °F/°C will flash. Use the + key to
select the °F or °C . Press and release the SET key to
confirm and exit the manual settings.
Please participate in the preservation of
the environment. Return used batteries to
an authorized depot.
MOON PHASES SYMBOL
The moon icon of the weather station will also display all 8
moon phases throughout the year according to the set
calendar. A bar segment above the moon phase will
indicate current moon phase.
FUNCTION KEYS:
Weather Station:
The Weather Station has 3 easy to use function keys: 1
key on the front, and 2 keys on the back
Bar segment (moon phase indicator)
MIN/MAX key
First
Waxing
Full
Moon
Waning Last
Quarter
Waning
Crescent
New
Moon
Waxing
Crescent
Quarter Gibbous
Gibbous
WEATHER FORECASTING ICONS:
The weather icons in the second section of LCD can be
displayed in any of the following combinations:
+ key
SET key
3
4
Indoor temperature
Indoor humidity
:
:
every 16 seconds
every 64 seconds
product is examined which is not in need or repair, you will
be charged for the repairs or examination.
Outdoor temperature and humidity: every 4 seconds
Transmission range
:
up to 260 feet (open space)
80 meters (open space)
The owner must pay any shipping charges incurred in
getting your La Crosse Technology, Ltd product to a La
Crosse Technology, Ltd authorized service center.
Power consumption (alkaline batteries recommended):
Weather station
:
2 x AAA, IEC LR3, 1.5V
Thermo-hygro transmitter
:
2 x AAA, IEC LR3, 1.5V
Your La Crosse Technology, Ltd warranty covers all
defects in material and workmanship with the following
specified exceptions: (1) damage caused by accident,
unreasonable use or neglect (including the lack of
reasonable and necessary maintenance); (2) damage
occurring during shipment (claims must be presented to
the carrier); (3) damage to, or deterioration of, any
accessory or decorative surface; (4) damage resulting
from failure to follow instructions contained in your owner’s
manual; (5) damage resulting from the performance of
repairs or alterations by someone other than an authorized
La Crosse Technology, Ltd authorized service center; (6)
units used for other than home use (7) applications and
uses that this product was not intended or (8) the products
inability to receive a signal due to any source of
interference.
Battery life
:
up to 12 months
Dimensions (L x W x H):
Weather station
:
:
3.72” x 0.78” x 6.18”
94.6 x 20 x 157mm
1.41” x 0.62” x 4.03”
36 x 16 x 102.6mm
Thermo-hygro transmitter
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited
warranty on this product against manufacturing defects in
materials and workmanship.
This limited warranty begins on the original date of
purchase, is valid only on products purchased and used in
North America and only to the original purchaser of this
product. To receive warranty service, the purchaser must
contact La Crosse Technology, Ltd for problem
determination and service procedures. Warranty service
can only be performed by a La Crosse Technology, Ltd
authorized service center. The original dated bill of sale
must be presented upon request as proof of purchase to
La Crosse Technology, Ltd or La Crosse Technology,
Ltd’s authorized service center.
This warranty covers only actual defects within the product
itself, and does not cover the cost of installation or removal
from a fixed installation, normal set-up or adjustments,
claims based on misrepresentation by the seller or
performance variations resulting from installation-related
circumstances.
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME
LIABILITY FOR INCIDENTAL, CONSEQUENTIAL,
PUNITIVE, OR OTHER SIMILAR DAMAGES
La Crosse Technology, Ltd will repair or replace this
product, at our option and at no charge as stipulated
herein, with new or reconditioned parts or products if found
to be defective during the limited warranty period specified
above. All replaced parts and products become the
property of La Crosse Technology, Ltd and must be
returned to La Crosse Technology, Ltd.
ASSOCIATED WITH THE OPERATION OR
MALFUNCTION OF THIS PRODUCT. THIS PRODUCT
IS NOT TO BE USED FOR MEDICAL PURPOSES OR
FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT
A TOY. KEEP OUT OF CHILDREN’S REACH.
Replacement parts and products assume the remaining
original warranty, or ninety (90) days, whichever is longer.
La Crosse Technology, Ltd will pay all expenses for labor
and materials for all repairs covered by this warranty. If
necessary repairs are not covered by this warranty, or if a
This warranty gives you specific legal rights. You may
also have other rights specific to your State. Some States
do no allow the exclusion of consequential or incidental
damages therefore the above exclusion of limitation may
not apply to you.
9
10
located or operating in conjunction with any other antenna
or transmitter."
Contact info for warranty or technical support:
La Crosse Technology
2817 Losey Blvd. S.
La Crosse, WI 54601
Statement according to FCC part 15.19:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Statement according to FCC part 15.21:
Modifications not expressly approved by this company
could void the user's authority to operate the equipment.
Product Info and Support:
Statement according to FCC part 15.105:
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Product Registration:
Contact Support: 1-608-782-1610
All rights reserved. This handbook must not be
reproduced in any form, even in excerpts, or duplicated or
processed using electronic, mechanical or chemical
procedures without written permission of the publisher.
This handbook may contain mistakes and printing errors.
The information in this handbook is regularly checked and
corrections made in the next issue. We accept no liability
for technical mistakes or printing errors, or their
consequences.
ꢀ
ꢀ
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
ꢀ
ꢀ
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
All trademarks and patents are acknowledged.
FCC ID: OMO-TX45U-TH-IT (transmitter)
FCC DISCLAIMER
RF Exposure mobile:
The internal / external antennas used for this mobile
transmitter must provide a separation distance of at least
20 cm (8 inches) from all persons and must not be co-
11
12
|