SPECIFICATION
GENERAL
LEGACY
Supply Voltage
Current Consumption
Power Output
Unit Dimensions
DC 13.8V. Negative Ground
Max.7A
40W X 4.
LCD75DFX
178[W] X 50[H] X 165[D] mm.
FM SECTION
Frequency range
87.5MHz -107.9MHz (USA)
87.5MHz -108.0MHz (EUR)
3uV.
Effective sensitivity
I.F Frequency
INSTRUCTION MANUAL
10.7MHz.
AM SECTION
Frequency range
530KHz - 1710KHz (USA)
522KHz - 1620KHz (EUR)
450KHz
I.F Frequency
RCA LINE OUT (OPTION)
Output
CD Max. 1200mv
CD PLAYER
System
Suitable CDs
Signal format
Compact Disc Audio System.
CD/CD-R/CD-RW Disc
Sampling frequency 44.1KHz.
No. of quantization bits 1bit.
20-100Hz <5dB
Frequency characteristics
10-20KHz <5dB.
50dB [1KHz]
2 STEREO channels.
S/N Ratio to CD
Number of channels
ANTI-THEFT FLIP DOWN DETACHABLE SYSTEM
AUTO-LOADING COMPACT DISC PLAYER
AM/FM-STEREO DIGITAL PLL TUNING RADIO
WITH INFRARED REMOTE CONTROLLER
11
BASIC OPERATING OF FUNCTIONAL KEYS
PRECAUTION OF DISC PLAY:
Cleaning the CD:
Before playing a CD, wipe it off with a clean, dust-free cleaning cloth.
Wipe the disc in the direction of the arrow.
Always insert the CD with the label side facing upwards.
If the CD is inserted with the printed side facing downwards, the device
may be damaged.
1. OPEN BUTTON
Press the OPEN button to fold down the front control panel.
Then a CD can be inserted into the CD slot or ejected by pressing
the EJECT button.
Note: If there is already a CD in the CD slot, do not try to insert a
second CD. For this may damage the device.
Always hold CDs by the edge. In order to keep the CD clean do not touch
the surface. Pull out the CD as the direction of follows.
2. RELEASE BUTTON
To remove the front control panel from the main body, poke at the
REL button downward to eject the front control panel.
3. SEL BUTTON (Select) AND +/- BUTTONS
a) Press the SEL button briefly to select the mode of sound mode item by
item, such as VOLUME, BASS, TREBLE, BALANCE and FADER.
Now the settings of them can be adjusted by using the + and - button.
(Note: If equalizer settings such as POP and ROCK have been selected
under DSP, it is impossible to change to BASS and TREBLE.)
b) Press the SEL button and hold for more than 1 second to access the
menu mode. Now press the SEL button briefly to select the menu mode
as follows: DSP (OFF / POP M / ROCK M / CLASS M / FLAT M), BEEP
ON/OFF, SEEK 1/2, VOL LAST/ADJ.
Do not attach any sticker or adhesive tape on the CD.
Do not expose the CD to direct sunlight or sources of heat such as
heating pipes.
DSP
In DSP mode you can select the equalizer settings POP M, ROCK M,
CLASS M and FLAT M, and DSP OFF by using the + and - button.
BEEP ON/OFF
Do not leave CDs in a car if it parked in direct sunlight as that will lead to
a considerable rise in the temperature inside the car.
You can select two types of confirmation beep by using the +/ - button.
BEEP ON: The confirmation beep can be heard whenever a button is
pressed.
Note: Do not use any solvents such as petrol or thinning agents.
Commercially available cleaning substances or antistatic spray will damage
the device.
BEEP OFF: The confirmation beep is switch off.
9
2
SEEK 1/ 2 (only available during radio operation)
Seek function with the or button during radio operation.
You can select SEEK 1/ SEEK 2 by using the +/- button.
SEEK 1: Keep the
or
stop at the next station that is detected.
buttons pressed down and the radio will
SEEK 2: As long as the
or
function will continue in the frequency band.
buttons are pressed down the search
VOL LAST/VOL ADJ
You can select VOL LAST or VOL ADJ mode by using the +/- button.
VOL LAST: The radio switches on at the actual volume it had when
it was last switched off.
VOL ADJ: Using the + and - buttons you can pre-select a constant
switch-on volume.
4. POWER ON/OFF
Turn the device on by using any button except the OPEN and the REL
button on the front control panel; Press PWR button and hold for
approximate two seconds to turn power off.
5.6. LCD (Liquid Crystal Display)
7. TUNE, SEEK, TRACK, SKIP UP / DOWN BUTTONS
a) During RADIO mode:
press the
Press the
or
or
button briefly to tune a frequency manually.
button and hold for more than one second to start
the automatic search for a radio station with a strong signal level.
(See also the function SEEK 1/SEEK 2.)
b) During CD mode:
press the button briefly to play next track. Press the button
briefly to play the current track from the beginning of the current track.
Press the
Press the
button twice continuously to play the previous track.
or button hold to skip forward or backward.
8. BAND BUTTON
Press the BND button briefly to select the radio broadcasting band
you would hear.
9. MODE BUTTON
Press the MODE button to select the CD playback or radio mode.
10-15. PRESET STATION MEMORY AND TOP, INT, RPT, RDM BUTTONS
a) During radio mode:
Press the six buttons briefly directly selects a preset radio station.
If the six buttons are pressed for more than 2 seconds, the station
currently being listened to is memorized into the selected preset
button.
3
8
b) During CD mode:
WIRING DIAGRAM
Press the TOP button briefly to interrupt the playback of the CD.
Press again to resume normal playback of the CD.
Press the TOP button and hold for approximately 2 seconds to play
the first track of the current disc.
ANTENNA PLUG
Press the INT button to play the first 10 seconds part of each track.
Press again to stop scan, while the currently selected track will be
played.
FUSE 7A
YELLOW
CONSTANT B+
BLACK(GND)
Press the RPT button to play the current track repeatedly. Press
again to cancel this function.
Press the RDM button to play all tracks on disc in random. Press
again to cancel this function.
RCA LINE OUT
GREY
RED R
FUSE 0.5A
WHITE L
ACC RED (B+)
FRONT
BLUE AUTO ANT
+
FRONT
+
WHITE
16. CLOCK BUTTON
-
WHITE/BLACK
GREY/BLACK
VIOLET
-
LEFT
SP
RIGHT
SP
Press the CLK button briefly to display time on the display, then press
the CLK button and hold until the real time flashes on the display.
And then press the + or - button to adjust HOUR or MINUTE.
+
+
GREEN
REAR
REAR
GREEN/BLACK
VIOLET/BLACK
-
-
Note:
17. SCAN BUTTON
Make sure use a speaker with 4 ohm load impedance to reduce
the distortion during high volume level.
Press the SCN button to scan the radio frequency. If a valid signal has
detected, the current frequency will be hold and blinked for 5 seconds,
then press SCN again to stop scan and remain the current frequency;
otherwise, the radio will go on to scan the other radio frequency fiver
seconds later.
For connecting speaker harness better and prevent to
short circuit, please have connecting refer to the process
as follow.
18. ST/MO BUTTON
During radio mode, press the ST briefly to select stereo or mono sound
mode.
19. INFRARED REMOTE CONTROL SENSOR
7
4
The Maintenance of Remote Control
OPERATION OF REMOTE CONTROL:
Note:
REPLACE THE BATTERY OF REMOTE CONTROL:
Before use this remote control, please make sure
turn on the device by pressing the power button on
the front control panel.
1.Remove the battery holder as the direction indicated by the arrow.
2.Replace the battery, Set a new battery properly with (+) side up.
3.Insert the battery holder. Push in the holder to the original position.
1. Power On/Off. 2. Mute Button
3. Loudness Button
Press this button briefly to enhance the bass
effect while the volume is low. Press again to
cancel the loudness effect.
4. Level/MENU UP Button
5.SEL/MENU Button
6. Level/MENU Down Button 7. MO/ST Button
8. A.P Button 9.Band Button 10. Mode Button
11.Tune/Seek Up And Track Skip Up/FF Button
12.Tune/Seek Down And Track Skip Down/REW Button
BATTERY INFORMATION:
Designated Battery: CR2025 3V
Battery Life: 6 months with normal use in normal room temperature, and
the out of date battery must be immediately removed and disposed properly.
CAUTION:
Improper use of batteries may cause overheating, explosion or ignition, and
resulting in jury or fire .
Battery leakage may cause damage to the unit.
Do not disassemble or short the batteries.
Do not throw the batteries into the fire.
13. SCAN BUTTON
15. LO/DX Button
14. Clock Display /Setting Button
At radio mode, press it to change local reception or distance reception.
And the LOC will showing on the LCD display when the receiver detect
some signal of stable local station.
To avoid the risk of accident, keep the batteries out of reach of children.
Note: This operation is only effective on FM reception. During AM mode,
LOC is ineffective.
16. CD Track TOP/Radio Preset 1
18. CD Track RPT/Radio Preset 3
20. Radio Preset 5
17. CD Track INT/Radio Preset 2
19. CD Track RDM/Radio Preset 4
21. Radio Preset 6
5
6
|