BIG BUTTON MEMORY PHONE
WITH VOLUME CONTROL
MODEL: PH-417
OPERATING INSTRUCTIONS
BIG BUTTONS FOR EASIER VIEWING & DIALING
RECEIVER VOLUME CONTROL
3 ONE-TOUCH MEMORY BUTTONS
INCOMING CALL INDICATOR LAMP
FLASH & REDIAL/PAUSE BUTTON
TONE/PULSE SWITCHABLE DIALING
DESK OR WALL MOUNTABLE
15 FOOT EXTRA LONG COIL CORD
•
•
•
•
•
•
•
•
PLEASE READ CAREFULLY BEFORE USE
IB-PH417-WM-E-022804
IMPORTANT TELEPHONE COMPANY & FCC INFORMATION
CAUTION: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND PERSONAL
INJURY, DO NOT OPEN CABINET.
WE SUGGEST THAT YOU REVIEW THE FOLLOWING INFORMATION PROVIDED BY
THE FCC (FEDERAL COMMUNICATIONS COMMISSION).
FCC REGISTRATION
This telephone set is registered with the FCC based upon compliance with Part 68 of its rules.
Connection of this telephone to the nationwide telecommunications network must be through
a standard network jack (RJ11W or RJ11C) which you can order from your telephone company,
if not already installed.
NOTE: FCC registration does not constitute an expressed or implied guarantee of
performance. Only the Limited Warranty in this booklet covers the performance of this
telephone set.
IMPORTANT FCC INFORMATION
In the event that terminal equipment causes harm to the telephone network, the telephone
company should notify the customer, if possible, that service may be stopped. However, where
prior notice is impractical, the company may temporarily cease service providing that they:
1. Promptly notify the customer.
2. Give the customer an opportunity to correct the problem with their equipment.
3. Inform the customer of the right to bring a complaint to the Federal Communications
Commission pursuant to procedures set out in FCC Rules and Regulations Subpart E of Part 68.
The telephone company may make changes in its communications facilities, equipment,
operations or procedures, where such action is reasonably required in the operation of its
business and is not inconsistent with the rules and regulations in FCC Part 68. If such changes
can be reasonably expected to render any customer terminal equipment incompatible, the
customer shall be given adequate notice in writing, to allow the customer an opportunity to
maintain uninterrupted service.
RINGER EQUIVALENCE NO. (REN):
The REN is useful to determine the quantity of devices you may connect to your telephone line and
still have all of those devices ring when your telephone number is called. In most, but not all areas,
the sum of the REN’s of all devices connected to one line should not exceed five (5.0). To be
certain of the number of devices you may connect to your line, as determined by the REN, you
should contact your local telephone company to determine the maximum REN for your calling area.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, try the following:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio/TV technician for assistance.
GENERAL
The FCC prohibits customer-provided terminal equipment to be connected to party lines or to
be used in conjunction with coin telephone service.
This phone is hearing aid compatible.
IB-PH417-WM-E-022804
2
CHECK LIST
Unpack your set, you should find:
MAIN SET
HANDSET
15 FOOT HANDSET CORD
(coil cord)
STRAIGHT TELEPHONE CORD
SHORT STRAIGHT CORD
(for wall mounting)
3
IB-PH417-WM-E-022804
LOCATION OF CONTROLS
16
1
15
14
12
11
13
10
2
9
3
8
4
7
5
6
1. COMFORTABLE ROUNDED HANDSET
2. 3 ONE-TOUCH MEMORY buttons - Allows you to speed dial emergency or other
frequently dialed numbers.
3. EXTRA LARGE KEYPAD buttons - For easier viewing & dialing.
4. REDIAL/PAUSE button - Redials your last number, useful when line is busy. And
also useful when dialing the number with pause.
5. INCOMING CALL INDICATOR lamp - Flashes when phone rings to show you call
is coming in.
6. FLASH button - For new dial tone or call waiting.
7. ADJUSTABLE HANDSET VOLUME CONTROL - Adjusts and raises volume of
receiver.
8. STORE button - Stores numbers into memory.
9. EXTRA LONG 15 FOOT COIL CORD
10. PHONE LINE jack (to Handset)
11. MEMORY INDEX PAPER (under the Handset)
12. REVERSIBLE HANDSET HOLDER (under the Handset) - For wall use, holds
handset in upright position.
13. TONE/PULSE switch - Suitable for computerized call directing also electronic
banking. Also works on older “Rotary” phone system.
14. RINGER ON/OFF switch - Turns off ringer for undisturbed privacy.
15. PHONE LINE jack (to Wall Jack)
16. WALL MOUNT SLOTS - (on the back of the set) For mounting onto wall.
4
IB-PH417-WM-E-022804
INSTALLATION INSTRUCTIONS
INSTALLATION
HANDSET
REAR OF THE
TO TELEPHONE
WALL JACK
TELEPHONE BASE
COILED HANDSET CORD
STRAIGHT TELEPHONE
CORD
To Telephone Jack
1. Insert the modular plugs of the COILED HANDSET CORD into the jack of the
TELEPHONE HANDSET and into the jack on the left side of the TELEPHONE BASE.
2. Insert the modular plugs of the STRAIGHT TELEPHONE CORD into the modular jack at
the REAR of the TELEPHONE BASE and into the TELEPHONE WALL JACK (either end
can be plugged in).
RINGER SETTING
This switch is located on the rear of the set. Select the desired function of the ringer.
ON - Normal setting of rings on incoming calls.
OFF - No rings on incoming calls.
NOTE: If your RINGER switch is in OFF position, only THIS phone will not ring, other
phones in your home on the same line will ring.
NOTE: Even if your RINGER switch is in OFF position, the indicator lamp will flash
when there is an incoming call.
TONE/PULSE SWITCH
Select the type of dialing that you desire or that your telephone system requires.
TONE - The phone will operate using tone dialing. (If your phone doesn’t dial out,
switch to PULSE.)
PULSE - The phone will dial using rotary pulse dialing.
NOTE: Even when your phone is set to pulse service, this phone can be switched to
temporary tone dialing for access to services that require tone signaling like
computer systems. Just press the
button after dialing in pulse and your
buttons can now be used for tone signaling for this call only.
5
IB-PH417-WM-E-022804
PHONE OPERATION
RECEIVING CALLS AS A NORMAL TELEPHONE
When the phone rings:
1. Lift the HANDSET and speak into the mouthpiece of the HANDSET.
2. Hang up the HANDSET when the conversation is completed.
MAKING CALLS AS A NORMAL TELEPHONE
1. Select the desired dialing mode with the TONE/PULSE switch (do this only the first
time).
2. Pick up the HANDSET and listen for a dial tone.
3. Dial your call.
LAST NUMBER REDIALING
The last number you called from the keypad can be redialed by pressing the REDIAL/
PAUSE button. This is useful if the number called is busy.
Get a new dial tone and press the REDIAL/PAUSE button. This phone will remember
the last number dialed even overnight. If you do not want anyone to know which
number you dialed last, pick up the phone and press any number & hang up.
PAUSE FUNCTION
If you make a dial with a pause in the number, simply press the REDIAL/PAUSE button
for the pause.
VOLUME CONTROL
You can adjust the sound level of the handset receiver by adjusting the RECEIVER
VOLUME setting.
INCOMING CALL INDICATOR
This lamp located near the RECEIVER VOLUME button will flash when the phone
rings. This is useful to see incoming calls and to locate the phone in a dark room.
NOTE: Even if RINGER switch is in the OFF position the lamp will flash.
TEMPORARY TONE DIALING
Temporary tone dialing is used only when you have older rotary service. It allows you
access to services that require tone signaling, including some tone-activated computer
system (e.g., telephone banking).
To change from pulse (rotary) to tone dialing during a call:
1. Dial a telephone number with the TONE/PULSE switch set to PULSE.
2. Press
button; all buttons pressed after this will send tone signals.
3. After you hang up, the phone automatically returns to rotary service.
IB-PH417-WM-E-022804
6
STORING PHONE NUMBER INTO MEMORY
LOCATIONS
NOTE 1. This phone has 3 ONE-TOUCH memories. This is very useful for emergency
numbers or numbers you call very often such as your parents or best friends.
To use the one-touch numbers, just get a dial tone and press one of the 3
buttons. To store a number into any of these 3 locations, just follow the
instructions below. Remember to write the names you stored onto the Memory
Index Card.
NOTE 2. It is important to write the emergency numbers into the Memory Index.
Occasionally, if phone is disconnected from line or moved from room to room,
or if the phone company has a problem on the line, it is possible for memory of
numbers to be lost, the manufacturer does not assume responsibility for
customer’s reliance on this memory feature.
STORING TELEPHONE NUMBERS
This telephone will store up to 15 digits in each memory positions. Follow this simple step
by step method.
1. Make sure the phone is plugged into the wall jack.
2. Lift the HANDSET and listen for a dial tone.
3. Press STORE button once.
4. Dial the number you want to store.
5. Press a memory number from M1 to M3 (where you would like your number stored).
6. Hang up the phone.
7. Repeat steps 2-6 to store the remaining numbers into M2 and M3.
TO DIAL NUMBER FROM 3 ONE-TOUCH BUTTONS
Get a dial tone by picking up HANDSET, and press one of the 3 emergency buttons marked
with the symbols M1, M2 or M3.
EXAMPLE: Suppose you want to store 1-212-555-1212 into MEMORY button #2(M2).
1. Lift the HANDSET.
2. Press the STORE button.
3. Dial 1-212-555-1212
4. Press M2.
5. Replace the HANDSET.
7
IB-PH417-WM-E-022804
STORING TELEPHONE NUMBERS INTO MEMORY LOCATIONS
NOTE 1. If you want to store a calling card number into one of your memories,
you may do this the same way you program a phone number into memory.
Also if you need a pause in the number, simply press the REDIAL/PAUSE
button on your phone.
NOTE 2. Emergency calling is an important safety feature that should be used
wisely. If you program an emergency number into the memory - mark it
clearly and test it before an emergency. We assume no responsibility
for customer’s reliance on this memory feature. Also if you test emergency
numbers, do so only during non-peak hours and tell the operator “This
is a test” or they may assume it is an emergency.
NOTE 3. If you move your phone to another room or disconnect the phone line,
your stored numbers will remain in the memory for a short time, so
quickly reconnect it to the new jack or you will have to re-program the
memory numbers.
NOTE 4. If the operator comes in during storing numbers with the message “your
phone is off the hook”, ignore this. During storing of numbers the circuit
simulates an off hook condition. This is normal. We suggest you program
the numbers quickly to avoid operator messages.
NOTE 5. In case you want to change a number, simply store a new number, the
old number will be automatically erased.
TO DIAL A NUMBER FROM MEMORY BUTTONS
1. Pick up receiver (to get dial tone).
2. Press the button in which the number you want to dial is stored, M1, M2 or M3, etc.
The set will dial the number stored in the memory you selected automatically.
EXAMPLE: Pressing M2 will dial (in TONE or PULSE) the number you stored in M2.
TO LIST YOU MEMORY NUMBERS
1. Lift out the Memory Index card from under the receiver.
2. Write numbers on Memory Index next to M1, M2, and M3 (in pencil so you can
change them later).
8
IB-PH417-WM-E-022804
WALL MOUNTING
The set can be mounted on a wall phone plate. If you do not have a modular wall phone
plate installed, we recommend that you consult with your telephone company or installer to
get one, or turn to page 10 for instruction.
1. Reversible HANDSET HOLDER - When the telephone is mounted on the wall, the
REVERSIBLE HANDSET HOLDER must be adjusted so it will hold the handset.
3.REPLACE INTO PHONE
2.REVERSE
1.SLIDE OUT
CONNECTING TO WALL PLATE
1. Use the SHORT STRAIGHT cord.
2. Plug one end into the PHONE LINE jack
(on the rear of the set).
3. Plug the other end into the wall jack.
4. Route the cord into the channel as
shown.
5. Put the phone over wall plate, make
sure both posts fit into slots on the back
of the phone. Then push down to lock
phone onto the wall plate.
9
IB-PH417-WM-E-022804
WALL MOUNTING
FOLLOW THESE INSTRUCTIONS TO MOUNT THE PHONE ON THE
WALL WITHOUT A WALL PLATE
Follow these instructions to mount the phone on the
wall without a wall plate:
1. Locate a wall stud. If it is possible to utilize a wall
Drill one hole
stud for mounting, dry wall expanders or a similar
type fastener is recommended. Consult your local
hardware stores for details.
15
2. Drill 2 holes 3
/
" (100 mm) apart.
16
Make sure space
between holes is
3
3. Put a screw into each hole and leave
/
" (5mm)
16
100 mm
of the head exposed to mount the phone (screws
are not included).
4. Connect the straight cord to the phone and jack.
5. Place the TELEPHONE BASE on the 2 mounting
screws and gently push down to lock into place.
Drill one hole
CLEANING AND MAINTENANCE
1. Keep the phone away from bathtub, water or very high heat and humidity (keep
away from stove or radiators).
2. Avoid placing it in very hot sun.
3. Do not staple phone cord.
4. Do not, under any circumstances, disassemble the telephone without disconnecting
the cord from the telephone line first. Ringer voltages can be high and dangerous.
5. Cleaning the exterior surface of the set should be done on a regular basis. Use a
cloth slightly dampened with warm, clean water to remove excess dust and dirt. Do
not use benzine, thinner, or the like, or any abrasive powder to clean the cabinet.
Wipe it with a soft cloth. The set should be kept free of dust, moisture and vibration,
and should not be exposed to direct sunlight.
6. DO NOT USE WAXES, SOLVENTS OR DETERGENTS OF ANY KIND TO CLEAN
YOUR UNIT. These products can damage the surface of the phone. Do not allow
any liquids to get inside the case.
10
IB-PH417-WM-E-022804
TROUBLE SHOOTING
PROBLEM
LIKELY CAUSES
1. Plug disconnected from jack.
2. Jack improperly wired.
No dial tone.
1. Damaged cord.
2. Jack improperly wired.
3. Line out of order.
Phone is dead.
Can make calls, but phone does RINGER switch in OFF position.
not ring.
Slide the switch to ON position.
1. If your other telephones are “ROTARY” type
phones, your line may be conditioned to
accept PULSE dialing only.
Move TONE/PULSE switch to PULSE position.
2. Contact your phone company to have your
line changed to TONE and PULSE service.
Can receive, but cannot make
calls.
Static noise on line or cannot hear
calling party or calling party
cannot hear you.
Replace the coil cord. Any phone store has
these cords in different lengths.
1. If problems with your telephone service occur later, try to determine if the trouble is
with the telephone or with the telephone company equipment. Unplug the telephone
and try it on another jack in a different room or in a neighborhood’s home to see if the
phone line is bad or the phone.
2. If disconnection of your equipment ends the problem, your telephone may be the
source of the trouble and it should be tested and repaired if necessary before it is
reconnected.
3. There are no user maintainable parts or adjustments on this set. Should your phone
require repair, contact us for instructions (except for cords which you can buy at
any phone store).
11
IB-PH417-WM-E-022804
LIMITED WARRANTY
We warrant this product to be free from defects in material and workmanship
under normal use for a period of 1 year after purchase and we will repair it free of
charge or replace it at no charge, should it become defective under this warranty,
providing you submit proof of purchase (sales slip) with the set.
During the initial 1 year period after original purchase, we will service or exchange,
at no charge, the set that is returned to LENOXX ELECTRONICS CORP. After the
initial 1 year period expires, we will repair the unit covering any part(s) that need to be
replaced at no charge, but will charge for the cost of labor, return postage paid by
LENOXX.
This warranty does not apply to any products which have been subject to
misuse, neglect or accident. This warranty does not cover broken cords or cabinet.
UNDER NO CIRCUMSTANCES WILL LENOXX ELECTRONICS CORP. BE LIABLE
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state. The following charges apply to repairs beyond the
warranty period: $5.00. Be sure to pack carefully and return postage paid insured
together with your money order (personal checks will not be accepted) and sales
receipt to :
LENOXX ELECTRONICS CORP. 2 GERMAK DRIVE, CARTERET N.J. 07008
For Customer Service
Dial: 1-800-315-5885 (MONDAY - THURSDAY 09:00 AM - 05:00 PM, FRIDAY 09:00 AM -
01:00 PM EST)
Or Visit Our Website: http://www.lenoxx.com
© 2004 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
12
IB-PH417-WM-E-022804
|