Lexmark Printer Accessories NO 31 User Manual

Refill instructions Lexmark No. 31 | No. 33 | No. 35 | No. 43  
Please carefully read these instructions, before starting refilling a cartridge. In order to avoid any soiling, always place a protective mat underneath the cartridge before starting the  
refilling process, and keep a dampened cloth at hand, to remove any contamination straight away. These instructions apply to the cartridges mentioned above only. The syringe  
and injection tools as well as the ink must be kept away from children. We shall not be held liable for damages caused by inadequate or wrong handling. The refilling of cartridges  
is made at your own risk. The refilling process has to be carried out before the cartridge is totally empty. Please note however, that ink cartridges with built-in print heads can not  
be refilled repeatedly.  
1.  
2.  
3.  
The ink tanks provided need to be turned into syringes in  
order to complete the refilling process. For this purpose,  
open the cap of one of the provided ink tanks. Place the  
included blunt needle by screwing it down the tank’s  
opening. Hold the base of the syringe with thumb and  
forefinger and twist the injecting devise onto it, counter  
clockwise.  
First remove the label from the upper side of the cartridge  
und bore refilling holes. To do so, use the supplied tool  
to enlarge the 3 existing openings.  
Now insert the syringe inclined into each opening.  
Slowly and carefully squeeze the ink into each ink  
chamber, until just under the openings. If some ink  
emerged from the nozzles, simply draw up a small  
quantity of ink from the chamber into the syringe.  
To make sure that you inject the right colour into the  
correspondent colour chamber while refilling, start to  
identify each colour chamber, inserting a toothpick  
through the openings. Replace the label afterwards.  
4.  
You can moreover use an empty syringe without needle  
to press air from above into the openings and by doing so  
produce a slight over pressure within the ink chambers.  
By doing so, ink will flow out of the nozzles and has to be  
dabbed away immediately with a tissue. This trick allows  
pressing sealed air bubbles out of the nozzle chamber.  
Finally clean the area around the nozzles with a tissue,  
until these are clearly visible. You may now insert the  
refilled cartridge into the printer.  
Additional information: If your printer is using more  
than 3 colours, you are required to mix photo ink for  
every colour. The proportions are as follow: 3/4 of the  
syringe filled with the Photo & Cleaning Fluid provided  
in our refill set, and 1/4 with the required colour of  
ink. Finally mix the solutions by shaking vigorously  
and proceed to fill the mixture into the respective ink  
chambers.  
Should the cartridge print in streaks, please start a  
cleaning cycle with your printer software. If the problem  
remains, dab the nozzles with a dampened cloth or leave  
them to settle in warm water for few minutes.  
You are facing difficulties refilling your ink cartridges or require more information about the refilling procedure? Please feel free to contact us. The address is as follow:  
ink.co.uk Customer Care Department PO Box 987 – Canterbury CT1 9EF [email protected]  
Logos, brand names and product descriptions are the property of their respective manufacturers and are used for reference purposes only.  
 

Kunz Lawn Mower C60K H60T H60B E60B User Manual
Land Pride Spreader PS25 Series User Manual
LevelOne Marine RADAR MIMO Wireless PCMCIA Adapter User Manual
LG Electronics Cell Phone P509 User Manual
Magic Chef Refrigerator MCBR1010S User Manual
Maha Energy Wheelchair D1 3602BA1 GB03 User Manual
Marantz Stereo Receiver SR4320 User Manual
MB QUART Car Stereo System ONX11000D User Manual
Memorex Clock Radio MSP CR1100 User Manual
Merco Savory Toaster Synergy User Manual