Makita Cordless Drill 6409 User Manual

INSTRUCTION MANUAL  
Drill  
6409  
6409N  
6410  
6409  
6409N  
6410  
004612  
DOUBLE INSULATION  
WARNING:  
For your personal safety, READ and UNDERSTAND before using.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
1
 
The technical documentation is kept by our authorised  
representative in Europe who is:  
7.  
Do not abuse the cord. Never use the cord for  
carrying, pulling or unplugging the power tool.  
Keep cord away from heat, oil, sharp edges or  
moving parts. Damaged or entangled cords  
increase the risk of electric shock.  
Makita International Europe Ltd,  
Michigan, Drive, Tongwell,  
Milton Keynes, MK15 8JD, England  
8.  
9.  
When operating a power tool outdoors, use an  
extension cord suitable for outdoor use. Use of  
a cord suitable for outdoor use reduces the risk of  
electric shock.  
30th January 2009  
000230  
If operating a power tool in a damp location is  
Tomoyasu Kato  
Director  
unavoidable, use  
interrupter (GFCI) protected supply. Use of an  
a
ground fault circuit  
Makita Corporation  
3-11-8, Sumiyoshi-cho,  
Anjo, Aichi, JAPAN  
GFCI reduces the risk of electric shock.  
Personal safety  
10. Stay alert, watch what you are doing and use  
common sense when operating a power tool.  
Do not use a power tool while you are tired or  
under the influence of drugs, alcohol or  
GEA005-2  
General Power Tool Safety  
medication.  
A
moment of inattention while  
operating power tools may result in serious  
personal injury.  
Warnings  
WARNING Read all safety warnings and all  
instructions. Failure to follow the warnings and  
instructions may result in electric shock, fire and/or  
serious injury.  
11. Use personal protective equipment. Always  
wear eye protection. Protective equipment such  
as dust mask, non-skid safety shoes, hard hat, or  
hearing protection used for appropriate conditions  
will reduce personal injuries.  
12. Prevent unintentional starting. Ensure the  
switch is in the off-position before connecting  
to power source and/or battery pack, picking  
up or carrying the tool. Carrying power tools  
with your finger on the switch or energising power  
tools that have the switch on invites accidents.  
13. Remove any adjusting key or wrench before  
turning the power tool on. A wrench or a key left  
attached to a rotating part of the power tool may  
result in personal injury.  
14. Do not overreach. Keep proper footing and  
balance at all times. This enables better control  
of the power tool in unexpected situations.  
15. Dress properly. Do not wear loose clothing or  
jewellery. Keep your hair, clothing, and gloves  
away from moving parts. Loose clothes,  
jewellery or long hair can be caught in moving  
parts.  
16. If devices are provided for the connection of  
dust extraction and collection facilities,  
ensure these are connected and properly used.  
Use of dust collection can reduce dust-related  
hazards.  
Save all warnings and  
instructions for future reference.  
The term "power tool" in the warnings refers to your  
mains-operated (corded) power tool or battery-operated  
(cordless) power tool.  
Work area safety  
1.  
2.  
Keep work area clean and well lit. Cluttered or  
dark areas invite accidents.  
Do not operate power tools in explosive  
atmospheres, such as in the presence of  
flammable liquids, gases or dust. Power tools  
create sparks which may ignite the dust or fumes.  
Keep children and bystanders away while  
operating a power tool. Distractions can cause  
you to lose control.  
3.  
Electrical safety  
4.  
Power tool plugs must match the outlet. Never  
modify the plug in any way. Do not use any  
adapter plugs with earthed (grounded) power  
tools. Unmodified plugs and matching outlets will  
reduce risk of electric shock.  
5.  
6.  
Avoid body contact with earthed or grounded  
surfaces such as pipes, radiators, ranges and  
refrigerators. There is an increased risk of  
electric shock if your body is earthed or grounded.  
Do not expose power tools to rain or wet  
Power tool use and care  
17. Do not force the power tool. Use the correct  
power tool for your application. The correct  
power tool will do the job better and safer at the  
rate for which it was designed.  
conditions. Water entering  
increase the risk of electric shock.  
a
power tool will  
3
 
18. Do not use the power tool if the switch does  
not turn it on and off. Any power tool that cannot  
be controlled with the switch is dangerous and  
must be repaired.  
could give the operator an electric shock.  
Always be sure you have a firm footing.  
Be sure no one is below when using the tool in  
high locations.  
3.  
19. Disconnect the plug from the power source  
and/or the battery pack from the power tool  
before making any adjustments, changing  
accessories, or storing power tools. Such  
preventive safety measures reduce the risk of  
starting the power tool accidentally.  
4.  
5.  
6.  
Hold the tool firmly.  
Keep hands away from rotating parts.  
Do not leave the tool running. Operate the tool  
only when hand-held.  
Do not touch the drill bit or the workpiece  
immediately after operation; they may be  
extremely hot and could burn your skin.  
Some material contains chemicals which may  
be toxic. Take caution to prevent dust  
inhalation and skin contact. Follow material  
supplier safety data.  
7.  
8.  
20. Store idle power tools out of the reach of  
children and do not allow persons unfamiliar  
with the power tool or these instructions to  
operate the power tool. Power tools are  
dangerous in the hands of untrained users.  
21. Maintain power tools. Check for misalignment  
or binding of moving parts, breakage of parts  
and any other condition that may affect the  
power tool’s operation. If damaged, have the  
power tool repaired before use. Many accidents  
are caused by poorly maintained power tools.  
22. Keep cutting tools sharp and clean. Properly  
maintained cutting tools with sharp cutting edges  
are less likely to bind and are easier to control.  
23. Use the power tool, accessories and tool bits  
etc. in accordance with these instructions,  
taking into account the working conditions  
and the work to be performed. Use of the power  
tool for operations different from those intended  
could result in a hazardous situation.  
SAVE THESE INSTRUCTIONS.  
WARNING:  
MISUSE or failure to follow the safety rules stated in  
this instruction manual may cause serious personal  
injury.  
FUNCTIONAL DESCRIPTION  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before adjusting or checking function on  
the tool.  
Service  
Switch action  
24. Have your power tool serviced by a qualified  
repair person using only identical replacement  
parts. This will ensure that the safety of the power  
tool is maintained.  
1. Switch trigger  
2. Lock button  
25. Follow instruction for lubricating and  
changing accessories.  
26. Keep handles dry, clean and free from oil and  
1
2
grease.  
GEB001-4  
003015  
SPECIFIC SAFETY RULES  
DO NOT let comfort or familiarity with product  
(gained from repeated use) replace strict adherence  
to drill safety rules. If you use this power tool  
unsafely or incorrectly, you can suffer serious  
personal injury.  
CAUTION:  
Before plugging in the tool, always check to see  
that the switch trigger actuates properly and  
returns to the "OFF" position when released.  
For Model 6409/6409N  
To start the tool, simply pull the switch trigger. Release  
the switch trigger to stop.  
For continuous operation, pull the switch trigger and  
then push in the lock button.  
To stop the tool from the locked position, pull the switch  
trigger fully, then release it.  
1.  
Use auxiliary handle(s), if supplied with the  
tool. Loss of control can cause personal injury.  
Hold power tool by insulated gripping  
surfaces, when performing an operation  
where the cutting accessory may contact  
hidden wiring or its own cord. Cutting  
2.  
accessory contacting  
a
"live" wire may make  
exposed metal parts of the power tool "live" and  
4
 
For Model 6410  
To install the bit, place it in the chuck as far as it will go.  
Tighten the chuck by hand. Place the chuck key in each  
of the three holes and tighten clockwise. Be sure to  
tighten all three chuck holes evenly.  
To remove the bit, turn the chuck key counterclockwise  
in just one hole, then loosen the chuck by hand.  
After using the chuck key, be sure to return to the  
original position.  
To start the tool, simply pull the switch trigger. Tool  
speed is increased by increasing pressure on the switch  
trigger. Release the switch trigger to stop.  
For continuous operation, pull the switch trigger and  
then push in the lock button.  
To stop the tool from the locked position, pull the switch  
trigger fully, then release it.  
For Model 6409N/6410  
Reversing switch action  
1. Sleeve  
2. Tighten  
3. Ring  
1. Reversing  
switch lever  
1
A
1
2
3
B
004629  
003553  
Hold the ring and turn the sleeve counterclockwise to  
open the chuck jaws. Place the bit in the chuck as far as  
it will go. Hold the ring firmly and turn the sleeve  
clockwise to tighten the chuck.  
To remove the bit, hold the ring and turn the sleeve  
counterclockwise.  
For Model 6410  
This tool has a reversing switch to change the rotational  
direction. Move the reversing switch lever to  
the position (A side) for clockwise (forward) rotation or  
the position (B side) for counterclockwise (reverse)  
rotation.  
OPERATION  
CAUTION:  
Drilling operation  
Always check the rotational direction before  
operation.  
Drilling in wood  
When drilling in wood, the best results are obtained with  
wood drills equipped with a guide screw. The guide  
screw makes drilling easier by pulling the bit into the  
workpiece.  
Use the reversing switch only after the tool comes  
to a complete stop. It will damage the tool to  
change the rotational direction before the tool  
stops.  
Drilling in metal  
To prevent the bit from slipping when starting a hole,  
make an indentation with a center-punch and hammer at  
the point to be drilled. Place the point of the bit in the  
indentation and start drilling.  
ASSEMBLY  
CAUTION:  
Always be sure that the tool is switched off and  
Use  
a
cutting lubricant when drilling metals. The  
unplugged before carrying out any work on the  
tool.  
exceptions are iron and brass which should be drilled  
dry.  
Installing or removing drill bit  
For Model 6409  
CAUTION:  
Pressing excessively on the tool will not speed up  
the drilling. In fact, this excessive pressure will only  
serve to damage the tip of your bit, decrease the  
tool performance and shorten the service life of the  
tool.  
1. Chuck  
2. Tighten  
3. Chuck key  
1
2
There is a tremendous twisting force exerted on  
the tool/bit at the time of hole breakthrough. Hold  
the tool firmly and exert care when the bit begins to  
break through the workpiece.  
A stuck bit can be removed simply by setting the  
reversing switch to reverse rotation in order to back  
3
004622  
5
 
out. However, the tool may back out abruptly if you  
do not hold it firmly. (For Model 6410)  
Always secure small workpieces in a vise or similar  
hold-down device.  
Avoid drilling in material that you suspect contains  
hidden nails or other things that may cause the bit  
to bind or break.  
MAINTENANCE  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before attempting to perform inspection  
or maintenance.  
To maintain product SAFETY and RELIABILITY, repairs,  
carbon brush inspection and replacement, any other  
maintenance or adjustment should be performed by  
Makita Authorized Service Centers, always using Makita  
replacement parts.  
ACCESSORIES  
CAUTION:  
These  
accessories  
or  
attachments  
are  
recommended for use with your Makita tool  
specified in this manual. The use of any other  
accessories or attachments might present a risk of  
injury to persons. Only use accessory or  
attachment for its stated purpose.  
If you need any assistance for more details regarding  
these accessories, ask your local Makita Service Center.  
Drill bits  
Keyless drill chuck(For Model 6410)  
Chuck key(For Model 6409)  
6
 
7
 
Makita Corporation Anjo, Aichi, Japan  
884093I229  
 

Lennox Hearth Stove SS210 User Manual
Lenoxx Electronics Furnace G60DFX User Manual
Lexicon Stereo Receiver RV 8 User Manual
LG Electronics Cell Phone VX3100A User Manual
Life Fitness Home Gym Smith Machine User Manual
Link electronic Network Router IEC 786 User Manual
Logitech Car Speaker Z506 User Manual
Logitech Webcam C270 User Manual
LOREX Technology Security Camera SHS 2S User Manual
Maytag Washer BRAVOSTM User Manual