Metra Electronics Automobile Accessories 99 2004 User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-2004  
APPLICATIONS  
Cadillac  
1997-2001 Catera  
1996-1999 Deville (Column Shift Only)  
99-2004  
KIT FEATURES  
• DIN Radio Provision with Pocket  
• ISO DIN Radio Provision with Pocket  
KIT COMPONENTS  
( A) Radio Housing • ( B) Trim Plate • ( C) ISO Brackets • (D) (4) Speed Clips • (E) (4) Phillips head screws  
D
B
C
A
E
TOOLS REQUIRED:  
Phillips Screwdriver  
Cutting Tool  
1-800-221-0932  
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION  
 
DASH DISASSEMBLY  
99-2004  
1997-2001 CADILLAC CATERA  
Disconnect the negative battery  
terminal to prevent an accidental  
short circuit.  
1
2
3
A
B
C
Remove (1) Phillips head screw from  
inside the ashtray and remove ash-  
tray. (Figure A)  
Remove screw covers from the radio  
trim panel. Remove traction control  
and hazard switch covers. Then  
remove switches by depressing tabs  
and pulling outward. (Figure B)  
Remove (4) Phillips head screws  
from behind covers and ashtray.  
4
5
Remove radio trim panel and unplug  
any remaining harnesses from the  
panel. (Figure C)  
Remove (2) Phillips head screws  
securing the radio. Unplug and  
remove the radio.  
6
1996-1999 CADILLAC DEVILLE  
A
Disconnect the negative battery  
terminal to prevent an accidental  
short circuit.  
1
Unsnap and remove radio trim panel.  
(Open glove box to access.) (Figure A)  
2
3
Pinch the side clips to disengage  
radio. Unplug and remove radio.  
1
 
KIT ASSEMBLY  
1997-2001 CADILLAC CATERA  
99-2004  
Remove (2) tabs from the top edge  
of the radio housing. (Figure A)  
Remove both mounting brackets “B”  
from the radio housing. (Figure B)  
1
2
B
A
TWO ON EACH SIDE  
OF RADIO HOUSING  
DIN RADIO PROVISION  
Slide the radio into the DIN  
cage/housing assembly until it snaps  
into place. (Figure B)  
4
Slide the DIN cage into the radio  
housing and secure by bending the  
metal locking tabs outward. (Figure A)  
3
B
A
Continue with final assembly.  
5
3
ISO RADIO PROVISION  
Align the holes from the ISO snap in  
Slide the radio bracket assembly into  
4
brackets with the holes in the side of  
the radio and mount the brackets to  
the radio using screws supplied with  
the radio. (Figure A)  
the radio housing until the assembly  
snaps into place. Snap the ISO  
Trimplate over the unit. (Figure B)  
A
B
Continue with final assembly.  
5
2
 
KIT ASSEMBLY  
1996-1999 CADILLAC DEVILLE  
99-2004  
Install (4) speed clips into the sub-  
dash mounting positions. (Figure A)  
Remove mounting brackets “A” from  
the radio housing. (Figure B)  
1
2
B
A
TWO ON EACH SIDE  
OF RADIO HOUSING  
DIN RADIO PROVISION  
Slide the radio into the DIN  
cage/housing assembly until it snaps  
into place. (Figure B)  
4
Slide the DIN cage into the radio  
housing and secure by bending the  
metal locking tabs outward. (Figure A)  
3
B
A
Continue with final assembly.  
5
3
ISO RADIO PROVISION  
Align the holes from the ISO snap in  
Slide the radio bracket assembly into  
4
brackets with the holes in the side of  
the radio and mount the brackets to  
the radio using screws supplied with  
the radio. (Figure A)  
the radio housing until the assembly  
snaps into place. Snap the ISO  
Trimplate over the unit. (Figure B)  
A
B
Continue with final assembly.  
5
3
 
FINAL ASSEMBLY  
99-2004  
FINAL ASSEMBLY  
Locate the factory wiring harness in the dash and make the connection as shown.  
Metra recomends using the proper mating adapter and making the connections as  
shown. (Isolate and individually tape off the ends of any unused wires to prevent  
electrical short circuit.)  
1
Re-connect the negative battery terminal and test the unit for proper operation.  
Reassemble radio and dash assemblies in reverse order of disassembly.  
2
3
FINAL WIRING CONNECTIONS  
Make wiring connections using the EIA color code chart shown below and the instructions included with the head  
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually  
tape off ends of any unused wires to prevent electrical short circuit.  
A
A)  
B)  
C)  
D)  
Strip wire ends back 1/2"  
Twist ends together  
Solder  
B
C
D
Tape  
METRA / EIA WIRING CODE  
12V Ignition / Acc . . . Red  
Right Front (+) . . . . . Gray  
12V Batt / Memory . . Yellow  
Ground . . . . . . . . . . . Black*  
Power Antenna . . . . . Blue  
Right Front (-). . . . . . Gray / Black  
Left Front (+) . . . . . . White  
Left Front (-). . . . . . . White / Black  
Right Rear (+). . . . . . Violet  
Amp Turn-On . . . . . . Blue / White  
Amp Ground . . . . . . . Black / White  
Illumination. . . . . . . . Orange  
Dimmer . . . . . . . . . . Orange / White  
Right Rear (-) . . . . . . Violet / Black  
Left Rear (+). . . . . . . Green  
Left Rear (-) . . . . . . . Green / Black  
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.  
All colors may not be present on all leads due to manufacturer’s specifications.  
4
 
99-2004  
NOTES  
5
 
INST992004  
1-800-221-0932  
REV. 12/06/07  
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION  
INST99-2004  
 

KWC Hot Tub Z534804931 User Manual
Lennox Hearth Stove 1900HT M User Manual
LG Electronics Blu ray Player BH10 User Manual
LG Electronics Headphones HBS700 User Manual
Magnat Audio Stereo Amplifier 400 1000 User Manual
Margaritaville Refrigerator NBMGDC1XXX User Manual
Matsushita Laptop CF 18JHU70TW User Manual
Maytag Dishwasher ADB3500AW User Manual
McCulloch Lawn Mower M12597RB User Manual
McCulloch Trimmer 250CXL User Manual