Sonic Alert Clock Radio SBT600ss User Manual

RHK900 (SBT600ss) for USA  
24-11-2014  
Sonic Boom Alarm Clock & Bed Shaker  
with 5-Level Dimmer & USB Charging  
Model SBT600ss  
OPERATION INSTRUCTIONS  
IMPORTANT – Please read these instructions carefully before use and retain for future reference.  
See operating instructions on back.  
– Use only the supplied adaptor to connect the unit.  
Warning: To prevent fire or shock hazard do not expose this appliance to rain or moisture.  
Before connecting to mains make sure that the requirements specified on the apparatus  
corresponds to the available power supply i.e. AC100-240V~, 50/60 Hz.  
– The ventilation should not be impeded by covering the ventilation openings with  
items such as, newspaper, table cloth, curtains, etc;  
– No naked flame sources, such as lighted candles should be placed on the apparatus.  
– It shall not be exposed to dripping or splashing and that no objects filled with liquids,  
such as vases, shall be placed on the apparatus.  
– Do not place the product in closed bookcases or racks without proper ventilation.  
– Where the mains plug is used as the disconnect device, the disconnect device shall  
remain readily operable.  
 
RHK900 (SBT600ss) for USA  
24-11-2014  
Setting the correct time –  
1) Press and hold the Time Set Button (1) at the same time press the Hour Button (2) to  
advance the clock display rapidly until the hour is correct.  
2) Press and hold the Time Set Button (1) at the same time press the Minute Button (3) to  
advance the clock display rapidly until the minute is correct.  
A lighted dot (8) in the upper left of the clock display indicated the time is PM. For AM time  
indication, the dot does not light up.  
Setting the alarm time –  
1) Press and hold the Alarm Set Button (4) at the same time press the Hour Button (2) to  
advance the alarm display rapidly until the hour is correct.  
2) Press and hold the Alarm Set Button (4) at the same time press the Minute Button (3) to  
advance the alarm display rapidly until the minute is correct.  
3) Make sure the alarm time is correctly set for AM or PM, the lighted dot (8) indicated PM.  
Please be sure to release the HOUR and MIN set buttons before releasing the ALARM button.  
Selecting 12 or 24 hours format –  
1) Press and hold the Hour button (2) for 6 seconds to enter the hour selection mode, release  
the Hour button (2) when the display shows "12 H" or "24 H".  
2) Press and release the hour button to toggle between 12 or 24 hours. If no selection is made  
within 4 seconds, then the last displayed hour format will be chosen and the display will  
return to the normal Time mode.  
Waking to Alarm –  
1) If only the buzzer is required, do not plug in the vibrator.  
2) Set desired volume using the Volume wheel (12) for buzzsound.  
3) If only vibrator is required, the plug in the vibrator into Vibrator socket (14) and turn off the  
volume by using the Volume wheel (12).  
4) If both the Buzzer and vibrator are required, plug in the vibrator and set the volume to the  
desired level.  
5) Set alarm wake time per instructions for setting alarm time above.  
Adjusting The Alarm Duration Time  
The default alarm duration time setting is 30 minutes, you may adjust the alarm duration between 1  
minute and 59 minutes as desired. To adjust the alarm duration:  
1) Press and hold the AL. SET button (4) for six seconds. The clock display will show the  
default alarm duration as ‘30’, release the AL. SET button.  
2) Press the MIN button (3) to adjust the alarm duration to the desired setting, from 1 minute to  
59 minutes.  
3) When the display is showing the desired alarm duration time, it will return to the normal  
clock mode after 3 seconds. The new alarm duration time setting becomes the new default  
and remains in the memory until you change it again.  
Shutting Off Alarm –  
Alarm can be shut off temporarily for the day or shut off permantently.  
1) When the alarm goes off, simply press the AL off button (4) the alarm will shut itself off for  
the day and come back on the next day at the same time if the alarm setting has not changed.  
2) To shut off the alarm permanently, slide ON/OFF Switch (5) to off positon. The alarm will  
not come on until ON/OFF Switch (5) is set to on position again.  
Snooze Operation–  
SNOOZE button (6) – press after alarm has sounded. The alarm will be turned off for 9 minutes for  
extra sleep. The alarm will come back again after 9 minutes. You may repeat many time up to 119  
minutes .  
 
RHK900 (SBT600ss) for USA  
24-11-2014  
Adjusting The Snooze Time  
The default snooze time setting is 9 minutes but you may adjust the snooze time between 1 minute  
and 30 minutes as desired. To adjust the snooze time:  
1) Press and hold the SNOOZE button (6) for four seconds. The clock display will show the  
default snooze time ‘9’. Release the Snooze button.  
2) Press the “ MIN“ button (3) to adjust the snooze time to the desired setting, from 1 minute  
to 30 minutes.  
3) When the display is showing the desired snooze time, it will return to the normal clock mode  
after 3 seconds. The new snooze time setting becomes the new default and remains in the  
memory until you change it again.  
Volume –  
To adjust the volume rotate the Volume wheel (2) until you have reach the desired level.  
Tone –  
Adjust the tone by rotating the Tone wheel (10) until you have reach the desired level.  
Dimmer Operation  
There is a 5-level brightness control for the LED display. Press the SNOOZE button (6) once to  
change the display brightness. The brightness will cycle from 5-4-3-2-1-2-3-4-5 (from bright to dim  
then from dim to bright).  
*NOTE*: The dimmer function will not work, when the clock is in snooze mode.  
Bed Shaker / Vibrator  
1) Attach the bed shaker jack to the back of the clock at VIBRATOR input (14).  
2) Place vibrator under mattress or pillow.  
USB Charging  
This alarm clock is equipped with a convenient USB charging port on the back panel that allows you  
to recharge many brands of mobile phones, portable music players, and other handheld devices that  
are supplied with USB charging cables. The output rating of the USB charging port is 500mA.  
To charge your device, connect the USB charging cable that was supplied with your handled device  
to the USB charging port (13) on the back panel of this alarm clock. Observe the charging indicator  
on your device to confirm that it is charging.  
Note: Charging time will vary depending on the charging current that your device requires.  
Therefore some devices will take longer to charge than others.  
Battery Backup –  
To use the battery backup, you can install 1 pieces of 9V size battery at the base of the clock under  
the battery cover (7). Please note the LED display will not show during power failure but the clock  
will still be running and keeping proper time until the power is restored.  
NOTE: For the best results it is recommended that the battery be changed every 6-8 months. If the  
clock is not used for a while, it is recommended to remove the battery to aviod leakage.  
DC 5V Power Input –  
Attach the DC power supply input to the back of clock labeled DC5V  
IN (11 ).  
GENERAL DATA  
UL listed Power Adaptor: AC100-240V~, 50/60Hz  
Power Consumption: Adaptor Output: DC5V  
USB Charging Port Rating: 500mA  
, 800mA  
 
RHK900 (SBT600ss) for USA  
24-11-2014  
CAUTION:  
TO REDUCE THE RISK  
OF ELECTRICAL SHOCK,  
DO NOT REMOVE THE  
COVER (OR BACK) FROM  
THE PRODUCT. NO USER  
SERVICEABLE PARTS  
INSIDE. REFER  
The Lightening flash and  
arrowhead within the  
triangle is a warning sign  
alerting you of dangerous  
voltage inside the product.  
The exclamation mark  
within the triangle is a  
warning sign alerting you  
of important instructions  
accompanying the product.  
SERVICING TO YOUR  
SONIC ALERT DEALER.  
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE  
TO RAIN OR MOISTURE.  
Normal function may be disturbed by strong electromagnetic interference. If this is  
the case, normal function can be resumed by simply unplugging and plugging of the  
power adaptor. If function does not resume, try moving the unit to another location.  
-
-
Attention should be drawn to the environmental aspects of battery disposal.  
this indicating separate collection for electrical and electroinc equipment.  
SONIC ALERT'S 1 YEAR LIMITED WARRANTY  
The Sonic Boom Alarm Clock is warranted against manufacturing defects in materials and  
workmanship for one (1) year from the date of purchase. Within this period Sonic Alert will  
repair or replace at our option without charge for parts and labor. Simply contact our customer  
service department to obtain an RA (return authorization number) and instructions on how to  
process your product for return. Call 1-888-864-2446 or e-mail to [email protected]. You'll  
need a copy of your receipt to process the return authorization.  
Sonic Alert Warranty Center, 1081 West Innovation Dr., Kearney, MO 64060  
Sonic Alert  
Sonic Alert 1050 East Maple Rd. Troy, MI 48083  
www.SonicAlert.com 1-888-864-2446  
Made in China  
 

Shark Pressure Washer SSG 503027E SSG 503027G SSG 503537E SSG 503537G SSG 603537E SSG 603537G User Manual
Shindaiwa Trimmer X7502863700 User Manual
Sony Digital Camera 4 130 938 121 User Manual
Sony Stereo Amplifier MONAURAL User Manual
Spalding Fitness Equipment 89231CA User Manual
Sterling Weather Radio S 8312 User Manual
Subaru Automobile Alarm H7110LS200 User Manual
Sunbeam Heating System 137117 User Manual
Sunbeam Microwave Oven SNM1502RAS User Manual
Sylvania Stereo System SRCD635 User Manual