RF Output Channel
If channel 3 is already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Hit [PLAY B] once.
4) After a few seconds, hold [PLAY B] on the unit for 3 seconds.
If you need additional operating assistance after
reading this owner’s manual or to order replace-
ment accessories, please call
Hint
• The RF output channel may
not change when you adjust
tracking during playback. In
this case, stop the playback,
and start the playback again.
After that, hold [PLAY B] on
the VCR for 3 seconds again.
Owner’s Manual
TOLL FREE : 1-800-968-3429
Video Cassette Recorder
or visit our web site at
•
The RF output channel will change to channel 4 from channel 3 and you
will see a playback picture.
6260VF
•
When a picture does not appear on the TV screen, repeat step 4).
5) Hit [STOP C] to stop playback.
1. Before Using Your VCR
StereoTV Connection
BasicTV Connection
VIDEO
IN
AUDIO IN
You can use the AUDIO OUT jacks
and VIDEO OUT jack on the back of
the VCR if your TV has Audio/Video
Input jacks. In this case, you need to
set the TV to external Line Input
Mode. Please refer to your TV’s
owner’s manual.
L
R
ANT
AUDIO
IN
L
OUT
IN
R
Antenna
Antenna
Cable TV
Signal
or
Cable TV
Signal
or
OUT
VIDEO
(Back of VCR)
OUT
IN
Audio/Video Cables
(Back of TV)
(not supplied)
ANT
IN
(Back of TV)
ANT
IN
OUT
VIDEO
OUT
AUDIO OUT
L
R
2
(Back of VCR)
Disconnect
(Back of TV)
3
OUT
Connect
Connect
RF Cable (supplied)
Front & RearTerminals
AUDIO OUT jacks
AUDIO IN jacks
Connect the audio cables here through to the audio
input jacks of a camcorder, another VCR, a stereo
amplifier, a stereo amplifier or an audio system.
Connect the audio cables coming from the
audio output jacks of a camcorder, another
VCR or an audio source here.
Plug the AC power cords of the VCR and TV into the AC outlets.
4
ANT
AUDIO
L
ANT IN jack
Connect your antenna or cable box here.
IN
ANT
AUDIO
IN
Hint for Cable Box or Satellite Box
L
OUT
IN
OUT
IN
R
R
VIDEO
OUT
ANT OUT jack
VIDEO
OUT
IN
OUT
To select channels of the cable box or
satellite box
1) Turn on the unit by hitting [POWER], then
hit [VCR/TV].The “POWER” and the
“VCR/TV” indicator on the front panel will
(Back of VCR)
(Cable box or
Connect the supplied RF cable to the
ANT
Antenna or
OUT
IN
IN
antenna input jack on your TV.
Satellite box)
Cable TV
IN
OUT
VIDEO OUT jack
E
OUT
signal
RF cable
(supplied)
Connect the video cable here through the video
input jack of a camcorder, another VCR or a TV.
VIDEO IN jack
(Back of TV)
Connect the video cable coming from the
video output jack of a camcorder, another
VCR or an audio-visual source (laser disc
player, video disc player, etc.) here.
appear, then press [CHANNEL
] to
Select this connection when you want to view
or record a scrambled channel. With this con-
nection, channels cannot be changed on the
unit. You can view or record ONLY the chan-
nels you have selected on the cable box or
the satellite box.
POWER
CHANNEL
MEN
select channel 3 or 4 (the same channel as
the output channel of the cable box or
satellite box).
VIDEO
L
-
AUDIO
-
R
TAPE IN
• If you use the channel 4, you need to
change the unit’s RF output to channel 4.
Refer to “RF Output Channel”.
2) At the TV, select channel 3 or 4 (the same
channel as you have selected at step 1).
3) On the cable box or satellite box, select the
channel you want to view or record.
Installing the Batteries for
the Remote Control
Install two AA batteries
(supplied) matching the
polarity indicated on
the bottom of the
Supplied Accessory
• Remote control
(NA376UD) with
two AA batteries
• RF cable
• Owner’s manual
(WPZ0901TM002) (1VMN20688)
• While you are recording, only the recorded
channel can be viewed.
remote control.
Printed in China
- 1 -
1VMN20688 / HJ411UD #####
3. Preparation for Use
Turn on the Unit for the FirstTime
To Add/Delete Channels
Clock Set Up
MENU
MENU
To Select a Channel
You can select a channel by using
the Number buttons on the remote
control.
Notes for using the Number but-
tons:
- M E N U -
- M E N U -
1
1
1
5
6
7
CLOCK SET
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
MONTH DAY
YEAR
Turn on the TV and set
it to channel 3.
1 0 0 3 MON 2 0 0 5
/
HOUR MINUTE AM/PM
0 5 – – – –
LANGUAGE SELECT
AUDIO OUT
LANGUAGE SELECT
AUDIO OUT
or
or
or
• If channel 3 is already occupied for broad-
:
TV STEREO
SAP
[ON]
TV STEREO
SAP
[ON]
casting, see “RF Output Channel” section.
or
•
When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number (for
example: 117, hit [1], [1], [7]).
Select the current hour.
or
• If the clock is not set, the
CLOCK SET screen
appears when you press
[MENU]. In this case, go
to step 2).
Remote Control TV Screen
2
POWER
LANGUAGE SELECT
• You must precede single-digit
channel numbers with a zero (for
example: 02, 03, 04 and so on).
CLOCK SET
B ENGLISH
FRANCAIS
ESPAÑOL
[ON]
MONTH DAY
YEAR
1 0 0 3 MON 2 0 0 5
/
2
3
CHANNEL SET UP
2
3
4
CLOCK SET
HOUR MINUTE AM/PM
0 5 4 0 – –
To Preset the Channel Again
1) Hit [MENU] until the main menu appears.
:
or
AUTO SET UP
MONTH DAY
1 0 – –
YEAR
– – – –
B MANUAL SET UP
/
or
2) Select "CHANNEL SET UP" by pressing
[PLAY B] or [STOP C]. Then, hit
[F.FWD g].
HOUR MINUTE AM/PM
– – – – – –
or
Select the current minute.
CLOCK SET
:
Select the current month.
3) Select "AUTO SET UP" by pressing
[PLAY B] or [STOP C]. Then, hit
[F.FWD g]. After scanning, the tuner stops
on the lowest memorized channel.
3
CH 01
MONTH DAY
YEAR
AUTO SET UP
1 0 0 3 MON 2 0 0 5
/
MANUAL SET UP
CLOCK SET
To Change the On-Screen Language
1) Hit [MENU] until the main menu appears.
HOUR MINUTE AM/PM
CHANNEL 30
ADD
(CATV)
0 5
:
4 0
P M AM
B PM
MONTH DAY
1 0 0 3
YEAR
– – – –
/
or
2) Select "LANGUAGE SELECT" by pressing
[PLAY B] or [STOP C]. Then, hit
[F.FWD g].
Do you connect the cable from the cable box
or the satellite box to the VCR’s ANT-IN jack?
HOUR MINUTE AM/PM
– – – – – –
or
Select “AM” or “PM”.
:
Yes
Select the channel to be
added or deleted.
3) Select "ENGLISH", "FRANCAIS" or
"ESPAÑOL" by pressing [PLAY B] or
[STOP C]. Then, hit [C.RESET/EXIT].
Select the current day.
Yes Hit [MENU] to
exit
• Refer to “Hint for Cable Box or
8
To exit the CLOCK SET
screen
Satellite Box” section on page 1.
No
4
5
MANUAL SET UP
No Please wait for a few minutes.
CLOCK SET
CHANNEL 30
DELETE
(CATV)
After scanning...
MONTH DAY
1 0 0 3
YEAR
2 0 0 5
or
/
• The tuner stops on the lowest memorized
channel.
or
HOUR MINUTE AM/PM
– – – – – –
:
• You can select only the channels memorized
in the unit by using [CHANNEL
• If "AUTO SET UP" appears on the TV screen
again, check the cable connections. Then, hit
[F.FWD g] once again.
Hint
].
Select “ADD” or “DELETE”.
• To go back one step, hit [REW h] (during
Hint
Select the current year.
steps 2 to 7).
• If you accidentally select Spanish or French
and need English: Hit [MENU] and choose
SELEC. IDIOMA, or SELECTION LANGUE.
Hit [F.FWD g] and select ENGLISH.
Finally, hit [C.RESET/EXIT].
• Your clock setting will be lost if either there
is a power failure or if this unit has been
unplugged for more than 30 seconds.
Hint
C.RESET
EXIT
To exit the
menu.
•
Repeat these steps only if either there
was a power failure or if this unit has been
unplugged for more than 30 seconds.
- 3 -
EN
4. Precautions
Precautions
Troubleshooting Guide
Install Location
For safety and optimum performance of
this unit:
If this unit does not perform properly when operated as instructed in this Owner’s
Manual, check this unit consulting the following checklist.
Important Copyright Information
Unauthorized recording or use of broad-
cast television programming, video tape,
film or other copyrighted material may
violate applicable copyright laws. We
assume no responsibility for the unau-
thorized duplication, use, or other acts
which infringe upon the rights of copy-
right owners.
PROBLEM
CORRECTIVE ACTION
• Install the unit in a horizontal and sta-
ble position. Do not place anything
directly on top of the unit. Do not place
the unit directly on top of the TV.
• Shield it from direct sunlight and keep it
away from sources of intense heat.
Avoid dusty or humid places. Avoid
places with insufficient ventilation for
proper heat dissipation. Do not block
the ventilation holes on the sides of the
unit. Avoid locations subject to strong
vibration or strong magnetic fields.
No power.
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
Timer recording is impossible.
• Make sure the timer recording is set correctly.
• Make sure the power is off.
• Make sure the VCR clock is set correctly.
Cannot go into Recording mode. • Make sure the tape has a record tab. If needed, cover the hole with
adhesive tape.
A Note about Recycling
Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing
[CHANNEL
].
This product's packaging materials are
recyclable and can be reused. Please
dispose of any materials in accordance
with your local recycling regulations.
Batteries should never be thrown away
or incinerated but disposed of in accor-
dance with your local regulations con-
cerning chemical wastes.
Cannot view a tape but the audio
is OK.
•
Head cleaning may be necessary. Refer to “Auto Head Cleaning” on
page 8.
• Make sure the VCR is not in the Menu mode.
No or poor playback picture.
• Change the RF output channel to CH4. Then select the same
channel on the TV.
Avoid the Hazards of Electrical Shock and
Fire
• Do not handle the power cord with wet
hands.
• Do not pull on the power cord when
disconnecting it from AC wall outlet.
Grasp it by the plug.
• Fine tune your TV.
TV programs cannot be seen nor- • Re-check the ANT-IN and ANT-OUT connections. See page 1.
mally.
• Hit [VCR/TV] on the remote control so that the VCR/TV indicator on
the unit disappears.
No operation from the infrared
Remote Control.
• Make sure the power plug is connected to an AC outlet.
• Check batteries in remote control.
Note to the Cable TV System Installer
This reminder is provided to call the
Cable TV system installer’s attention to
Article 820-40 of the NEC that provides
guidelines for proper grounding and in
particular, specifies that the cable
ground should be connected to the
grounding system of the building, as
close to the point of cable entry as pos-
sible.
Video or color fades in and out when • You cannot copy a copyrighted video tape. You are experiencing copy
making a copy of a video tape.
guard protection.
Moisture Condensation Warning
Specifications
Moisture condensation may occur inside
the unit when it is moved from a cold
place to a warm place, or after heating a
cold room or under conditions of high
humidity. Do not use the unit at least for
2 hours until its inside is dry.
Video Heads :
Operating temperature : 41°F~104°F
Four Heads
Power requirement : 120V, 60Hz
Power consumption : 14 Watts
(5°C~40°C)
VHF Channel 3 or 4
Dimensions :
W 14-3/16" (360mm)
Converter output :
H 3-5/8" (92mm)
D 8-9/16" (216mm)
4.0 lbs. (1.8 Kg.)
(approx.)
Weight :
CAUTION:
FCC Warning
TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
ATTENTION:
• Designs and specifications are subject to change without notice and legal obligation.
• If there is a discrepancy between languages, the default language will be English.
This equipment may generate or use
radio frequency energy. Changes or
modifications to this equipment may
cause harmful interference unless the
modifications are expressly approved in
the instruction manual. The user could
lose the authority to operate this equip-
ment if an unauthorized change or modi-
fication is made.
POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRE-
SPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or
special waste.Contact your council for details.
- 4 -
EN
5. Playback
Turn on the TV and set it to
channel 3.
7. Other Operations
To cue or review picture during play- To play back in slow motion
Before:
1
back (Picture Search)
Hit [SLOW] during playback or the still mode.
• If the noise bar appears on the TV
screen, you can reduce it by pressing
POWER
Hit [F.FWD g] or [REW h].
• Hit it again and the VCR will now
search in super high speed. (in the
LP/SLP modes only.)
EJECT
1
VCR/TV
3
4
3
• If channel 3 is already occupied for broad-
casting, see “RF Output Channel” section.
2
5
8
0
[CHANNEL
].
CHANNEL
4
6
To temporarily stop recording
SEARCH
-MODE
Remote Control TV Screen
2
4
7
9
1
3
(Pause mode)
CHANNEL
MENU REC/OTR STOP/EJECT
REW
PLAY
F.FWD
To freeze the picture on TV screen
TAPE IN
C.RESET
EXIT
MENU
SLOW
during playback (Still mode)
Hit [PAUSE/STILL].
PLAYB
PAUSE
/STILL
REC/OTR SPEED
DISPLAY
Hit [PAUSE/STILL]. Each time you hit
the button, the picture will be forwarded
by one frame.
• During the rec pause mode, five
C
TAPE IN
marks appear on the TV screen. Each
mark represents one minute.
C
3 2
4
• If the picture begins to vibrate vertically • Hit it again to resume recording.
2
during the still mode, stabilize the pic-
Auto Rewind
Hint
ture by pressing [CHANNEL
].
EJECT
When a tape reaches its end during play-
back, fast-forward, or recording (except
timer recording and One Touch
Recording), the tape will automatically
rewind to the beginning. After rewinding
finishes, the unit will eject the tape and
turn itself to off.
STOP
EJECT A
• If the picture is distorted or rolling verti-
cally, adjust the vertical hold control on
your TV if equipped.
•
When a tape without record tab is inserted, the unit will start playback auto-
matically at step 1).
• Tracking will be automatically adjusted upon playback. To adjust the tracking manu-
ally, press [CHANNEL ].
Counter Reset
Hit [C.RESET/EXIT].
6. Recording & OTR (One Touch Recording)
Hint
Before:
• Still/Slow/Pause mode will be automatically cancelled after 5 minutes to prevent damage to the tape and the
2
Turn on the TV and set it to
video head.
• To return to playback from the Picture Search/Still/Slow mode, hit [PLAY B].
channel 3.
•If channel 3 is already occupied for
1
4
2
6
broadcasting, see “RF Output Channel” section.
POWER
EJECT
1
VCR/TV
3
8. On-Screen Operations
Remote Control TV Screen
1
2
2
5
8
0
with tab
CHANNEL
4
6
1
4
7
2
5
8
0
3
6
9
1
2
3
4
To call up the main menu
CHANNEL
SEARCH
-MODE
CH12
7
9
- M E N U -
MENU
CHANNEL
MENU REC/OTR STOP/EJECT
REW
PLAY
F.FWD
C.RESET
EXIT
TAPE IN
MENU
SLOW
TAPE IN
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
Select the chan-
nel to record.
PAUSE
/STILL
REC/OTR SPEED
DISPLAY
4
3
5
CHANNEL
MENU REC/OTR STOP/EJECT
REW
PLAY
F.FWD
LANGUAGE SELECT
TAPE IN
5
6
Select the desired tape
speed.
3
SP
SPEED
To select an item
Tape Speed
Recording/Playback Time
Type of tape
SP mode
SLP mode
T60
T120
2hours
6hour
T160
2-2/3hours
8hour
- M E N U -
1
4
2 3
1hour
3hour
or
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
Accidental erasure prevention
REC/OTR
4
LANGUAGE SELECT
To prevent accidental recording on a record-
ed cassette, remove its record tab. To record
on it later, cover the hole with adhesive tape.
REC
POWER
To decide
EJECT
1
VCR/TV
Hit [REC/OTR] repeatedly to select the desired
recording length.
2
5
8
0
3
6
Record tab
CHANNEL SET UP
CHANNEL
4
REC
OTR(0:30)
OTR(1:00).....
(Normal recording)
AUTO SET UP
SEARCH
-MODE
7
9
B MANUAL SET UP
OTR(8:00)
OTR(7:30)
C.RESET
EXIT
MENU
SLOW
4
3
4 1
2
EJECT
PAUSE
/STILL
5
6
Hint
REC/OTR SPEED
DISPLAY
STOP
EJECT A
To exit the menu
C.RESET
EXIT
MENU
• If you have connected this unit to a cable box or satellite box, refer to “Hint for Cable
Box or Satellite Box” section on page 1.
or
- 5 -
EN
|